WEBWEBTRANSMITTERSNS-100 Owner's Manual(Version 1.11)

10Installing SNS-100The fluctuation of operation voltage must be within 10% of the regulation voltage,and the electric outlet must be always grounded.

11Cautions in InstallationBe aware of the following cautions when installing SNS-100.● Always turn the power off before SNS-100 installation.● Severe

12● Position it in an open space with flat surface, keeping the aptitude temperature.Also, maintain the clearance between back of the main body and th

13Always use a dry cloth when cleaning this product. If the contamination is serious,please wipe it first with a neutral detergent, then with a dry c

14UnpackingWhen you purchase SNS-100, after removing the wrap, place the product on a flat surface or where youwill be installing it. Then, check if

15 OUTVTR, DVDP, TVChapter 3. Connecting to InstrumentsCautionCautionYou may connect the following items with SNS-100, such as video image players (e.

16SNS-100 produces the video image signal of the corresponding channel, if connected with externalinstruments to video out 1~4 (loop through RNC). Th

17Cable ModemRS-232C ETHERNET DC 5VALARMRS-485RS-232C ETHERNET DC 5VALARMRS-485RJ45 Ethernet Cable(Direct)RJ45 Ethernet Cable(Direct)Cable ModemCable

18Connecting to Alarm SensorConnect the alarm sensor as shown in the above diagram to perform alarm-processing function.ALRAMSENSOR1SENSOR2SENSOR3SENS

19Connecting to PAN/TILT/ZOOM/FOCUS Camera/ControllerRS-485 Half Duplex ModeThe ‘+,’ ‘-’ terminals of RS-485 on the rear of SNS-100 support Half Duple

2[Power Adapter]You must use only a compatible power adapter enclosed in SNS-100 package.[Fuse]You must use only an identical fuse (250V, T3.15A) used

20Connecting Pelco Dome Camera in RS-422 Full Duplex TX Mode.What is RS-422 Full Duplex TX Mode?SNS-100 only transmits the control signal to adjust PA

21Connecting a receiver for P/T/Z/F in RS-422 Full Duplex TX Mode.When the PAN/TILT/ZOOM/FOCUS receiver supporting RS-422 Full Duplex, do not connect

22Connecting to RS-232CWhen connecting PC serial port (COM1, COM2) through RS-232C from back of SNS-100, you mayselect console mode of SNS-100 by usin

2311142371325235969Pin Female to 9Pin FemaleTerminal Emulation Communication Set-upItems ContentsBaud Rate 38400 BpsData Bit 8 BitParity NoneStop Bit

24RS-232C ETHERNET DC 5VALARMRS-485Connected from SNS-100 to Direct PC(Twist Cable)RS-232C ETHERNET DC 5VALARMRS-485Creating Ethernet CableSince the E

25No information upon network is set up except Ethernet (MAC address) in factory defaults. You must setup the IP address when installing.Before You B

26Setting In Ethernet (10BaseT/100BaseT)For Windows 95/98/NT(1) Open Dos window from network-connected PC with SNS-100.(2) Execute "arp -s".

27(4) Wait until you receive the normal response after executing "ping".(5) If you are getting no response, attempt 1~2 more times. If you

28Setting in Unix(1) Execute the following instruction for network-connected Unix machines with SNS-100.(2) Execute "rarp -s".(3)Confirm if

29(4) See if you receive the normal response as shown below after executing "ping".(5) If you do not get responses, type "Ctrl+C"

3Note: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These lim

30Please, refer to Chapter 5 and 7 for log-in and administration mode network setting up.NoteSetting Other Network InformationAfter successfully setti

31In Cable Network through Cable Modem(1) Connect according to "Connecting to Cable Modem"of Chapter 3 Connecting to Network, and turnthe SN

32Chapter 5 SNS-100 LoginAfter successfully setting up an IP address as in Chapter 4, execute a web browser (Netscape orExplorer) from an Internet PC.

33(3) If you have properly logged in, you will see the following.(4) Properly enter user name and password and click "OK" icon. You should

34(4) Enter the SNS-100 IP address in Address : xxx.xxx.xxx.xxx(5) If you have properly logged in, you will see the following.(6) Properly enter user

35(7) Click "Yes". You just have completed downloading Explorer plug-in program from SNS-100. Then, you will see the initial screen of Cha

36Others(1) The initial user name and password in factory defaults are as follows.● User Name : root●Password : w2000(2) Log-in window appears only un

37Initial Screen(1) If you have entered correct user name and password or clicked "Application"button, you will see thenext initial screen o

38Quadruplex Screen(1) Click "Quad"button on left side of the screen. You will see 4 individual screens in the quadruplex screen.(2) Click a

39Single Screen with PAN/TILT/ZOOM Controller(1) After enabling Pan/Tilt/Zoom in Administration mode, if you select an image from "Camera 1~4&quo

4Chapter 1. SNS-100 Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6Overview- - - - - - - - - - - - - -

40Chapter 7 Administration ModeInitial Screen(1) You must enter "root" for the user name and its password in the log-in window to transfer t

41Camera Set-up(1) You will see the following screen by clicking "Camera"icon in Administration mode.(2) SizeAs the size of image in the scr

42(6) Pan/Tilt/ZoomSelect "Disable", if Pan/Tilt/Zoom controller is not connected. At this time "Preset"button isinactivated.If P

43PAN/TILT/ZOOM Set-up(1) You will see the next window, if you click "P/T/Z" icon in administration mode.(2) DeviceTo control PAN/TILT/ZOOM/

44Quad/Sequential Set-up(1) You will see the next screen by clicking Quad/Sequential icon in Administration mode(2) Quad SizeSelect from either Small

45Web Transmitter Set-up(1) You will see the next configuration window by clicking "Web Transmitter"in Administration mode.(2) Select date a

46③ Pswd EnableRestricts the access from other users. If you check the check box of "Pswd Enable"and click"Apply"button, you shou

47(5) Factory DefaultIf you click "factory default" button, all information or configuration of SNS-100 will return to the point ofpurchase,

48Alarm Set-up(1) Connect to an alarm sensor, referring to Chapter 3 Connecting to Instruments. Alarm terminal 1~4level is as shown below, when alarm

49(7) MessageSpecifies Alarm Message to transfer when the Alarm is raised and maximum 30letters can be entered. It is available only when "Mail&q

Chapter 7. Administration Mode -----------------------------------40Initial Screen--------------------------------------------------40Camera Set-u

50Network Set-up(1) You will see the next configuration window by clicking "Network"in Administration mode.(2) IP AddressEnter SNS-100 IP Ad

51(7) GatewaySet up the Gateway Address assigned by the network manager.(8) DHCP (Dynamic Host Configuration Protocol)DHCP is protocol, which automati

52Specifies the FTP Server address to send still image. The server address has to be either network IP Address where SNS-100 can access or Host Name.S

53File Transfer SettingClick "File Server" at Administration Mode to open the following window and to specifythe file transfer through the F

54BetweenSpecifies the starting and finishing time of image file transfer. It only applies to fileswhich were set as "Every" or "Both&q

55Custom User Interface SetupClick "WebBrowser" icon at Administration Mode to open "Custom User InterfaceSetup" window as follows

56About / Support / Help(1) AboutProvides you information on SNS-100.(2) SupportSamsung Electronics’ English Version Homepage(http://www.samsungelectr

57(3)HelpProvides you with help messages on each function.You can see help message as shown below by clicking in the configuration window of A

58WEBAPPENDIX ASNS-100 SPECIFICATIONS

59APPENDIX A SNS-100 SPECIFICATIONSSPECIFICATIONSVideo In/Out● Composite 4 Channel, Color & Black/White● NTSC/PAL compatible ● BNC Type● Loop Thro

6Chapter 1 SNS-100 OverviewOverviewSNS-100, connected to surveillance cameras or other external devices, compresses video image asmotion JPEG through

60Performance● Max 25 Frame/Sec (1 User Single Mode Connection)Alarm● Input 4 Port● TTL Level "Low"Active● Sends the captured screen through

61Regulation ApprovalNote: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the

62WEBAPPENDIX BFactory Default

63APPENDIX B Factory DefaultItems Factory Default ValueCamera 1~4 Size NormalVideo Quality LowTex

64All network-related information but Ethernet Address will be deleted.Therefore, you must be extremely careful when you execute this function.Warning

65WEBAPPENDIX CHow to Use Console

66Console allows condition check-up of SNS-100 by connecting to RS-232C port, manually setting network-related information.Starting Console(1) Connect

67(2) When you correctly enter user name "root"and password, the following message will appear.Command(1) help: Indicates Command itemsLaunc

68(2) ping: Indicates the connection status to a given IP address(3) status: Indicates the current condition and information of SNS-100SNS-100> pin

69--P/T/Z parameterdriver: <None>serial : 2400 bps, data 8, stop 1, parity 0ptz address 0123ptz preset setting list(0) id0, name <None>tot

7Upgraded Functions of VERSION 1.1You can send video image files through FTP server at certain time or in regular intervals. Users canaccess the FTP s

70Manual Configuration Mode(1) Once you turn the power on and SNS-100 functions normally, the following message will appear, and if you press any key,

71(4) If you enter "c" when "Select items?" appears, you will be provided with the menu, which will allow youto manually set the n

72(5) If there is information you would like to change or update, you can do so at this time. (6) If you enter "c" when "Select items?&

73WEBAPPENDIX DDynamic IP Information Transfer

74Appendix D Dynamic IP Information TransferIn such an environment where you have to be assigned with Dynamic IP as CableModem, you need separate meth

75Enter "5" and go to IP notify-mail address to type email address you want.Enter "4" and go to IP notify-mail enable/disable and

76When all the network settings are properly installed and DHCP function is enabled,Dynamic IP information is sent to the email, which was set while S

77Type "1" and go to IP auto-regist server address" to type registered web server address.The example below is the IP Address such as 1

78%g : Ethernet address (standard) Example: 00-00-f0-ff-a1-42%i : IP Address (dotted decimal) Example: 168-219-44-137%u : IP Address (32bit unsigned i

79Setting with the Browser When you have SNS-100 address and can access through the Web Browser, you canchange the setting as above at the Administrat

8①Video In②Video Out(Loop Through Out)③Control S/W④RS485 S/W ⑤Network LED⑥Power LED⑦Preset Button⑧Reset Button21657843Names and FunctionFamiliarize yo

80WEBAPPENDIX EFAQ

81APPENDIX E FAQAs you continue to use SNS-100, there could be some cases, which we have not yet discussed in thismanual. In such a case, it might a

82(2) If LED of Network for SNS-100 is working correctly, the values for Network within SNS-100 might have been incorrectly entered. In such a case,

83When the post-version software still operates, even after you have installed the updated version.When you upgrade to the latest version of the sof

84"Strange start marker" or "Not jpeg image" messages appear when accessed SNS-100 through the Internet Explorer. Or you cannot c

EELLEECCTTRROONNIICCSSAB68-00195A

9Rear of SNS-100Connects to maximum of 4 alarm sensors.Connects to RS-485 cable and remotely regulate PAN/TILT/ZOOM/FOCUScontrollers.❈Currently, only