Samsung SRP-370 Manual do Utilizador

User’s Manual SRP-370/372 Ver.2 Thermal Printer Rev. 2.04 http://www.bixolon.com

Rev. 2.04 - 10 -SRP-370/372 Ver.21-2-3 USB Interface POWER DKUSB Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Fram

Rev. 2.04 - 11 -SRP-370/372 Ver.21-4 Setting the Dip Switches 1-4-1 Serial Interface Switch No. Function ON OFF Default SW1-1 ON SW1-2 Baud Rat

Rev. 2.04 - 12 -SRP-370/372 Ver.21-4-2 Parallel & USB Interface Switch No. Function ON OFF Default SW2-1 OFF SW2-2 OFF SW2-3 Select Print De

Rev. 2.04 - 13 -SRP-370/372 Ver.21-5 Setting the Memory Switches This printer has “Memory Switch” set which is software switches. Memory Switch set

Rev. 2.04 - 14 -SRP-370/372 Ver.2 MSW2-8 MSW2-7 MSW2-6 MSW2-5 MSW2-4 MSW2-3 Character Table OFF OFF OFF OFF OFF OFF Page 0 437 (USA, Standard Europ

Rev. 2.04 - 15 -SRP-370/372 Ver.21-6 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the specifications. Do not u

Rev. 2.04 - 16 -SRP-370/372 Ver.21-6-5 Be sure to note the correct direction that the paper comes off the roll. 1-6-6 Pull out a small amount of p

Rev. 2.04 - 17 -SRP-370/372 Ver.21-7 Adjustments and Settings It has 2 features ; Paper end and Black mark. For detecting Paper End, it must be

Rev. 2.04 - 18 -SRP-370/372 Ver.21-8 Using the Printer Control Panel 1-9 Connecting the computer You need an appropriate interface cable

Rev. 2.04 - 19 -SRP-370/372 Ver.21-10 Connecting the Power Supply ※ CAUTIONS When connecting or disconnecting the power supply from the printer, mak

Rev. 2.04 - 2 - SRP-370/372 Ver.2 Safety Precautions In using the present appliance, please keep the following safety regulations in order to preve

Rev. 2.04 - 20 -SRP-370/372 Ver.22. Self Test The self-test checks whether the printer has any problems. If the printer does not function properly,

Rev. 2.04 - 21 -SRP-370/372 Ver.23. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. Thi

Rev. 2.04 - 22 -SRP-370/372 Ver.24. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) 203 X 203 dpi (8dots/m

Rev. 2.04 - 23 -SRP-370/372 Ver.25. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the

Rev. 2.04 - 3 - SRP-370/372 Ver.2 CAUTION Violating following instructions can cause slight wound or damage the appliance. Do not use the

Rev. 2.04 - 4 - SRP-370/372 Ver.2 Warning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device p

Rev. 2.04 - 5 - SRP-370/372 Ver.2 Introduction The SRP-370/372 Roll Printer are designed for use with electronic instruments such as system ECR, PO

Rev. 2.04 - 6 - SRP-370/372 Ver.2 Table of Contents 1. Setting Up the Printer ...

Rev. 2.04 - 7 - SRP-370/372 Ver.21. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or m

Rev. 2.04 - 8 - SRP-370/372 Ver.21-2 Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector pan

Rev. 2.04 - 9 - SRP-370/372 Ver.21-2-2 Parallel Interface (IEEE1284) POWER DKPARALLEL Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1